Skip to content
SEINA-3D
water leveltrigger

Simulation time

t = –

loading…

Loading case…

§ 02Results

KROTOS K42: steam explosion

Melt mass
1.54 kg
Melt temperature
2465 K
Water depth
1.13 m
Peak overpressure
64.8 MPa
Time shown
0–2 ms

A 1.54 kg alumina–water premixture is set off by a trigger at 0.35 m. Within 2 ms a pressure wave runs up and down the premixture, the 4 mm melt drops shed fine fragments that cool within a millisecond, and steam lifts the pool above its 1.13 m water level. The premixture and the trigger are prescribed, based on KROTOS K42.

Table 1 · Conditions

Melt
1.54 kg alumina (Al₂O₃) at 2465 K, as 4 mm drops falling at 3 m/s
Premixture
0–1.12 m; melt 1.7 % and steam 1.0 % of the volume
Water
1.13 m deep, 293 K
Pressure
0.10 MPa, with steam above the water
Vessel
0.177 m × 0.177 m square column, 2.13 m high (the cross-section of a 0.20 m tube)
Trigger
Prescribed at 0.35 m on the axis
Probes
K1–K5 on the wall at 0.15, 0.35, 0.55, 0.75 and 0.95 m
Grid
4 × 4 × 96 cells; 17.7 mm layers in the premixture; the lowest 1.5 m are shown
Shown
81 saved states, 0–2 ms, 25 µs apart

Reading the view

  1. The map on the right plots one field against height and time; overpressure, the pressure above the initial 0.10 MPa, is shown first. Each pixel column is a saved state, coloured by the mean over the 16 cells of that layer. Hover to read the mean and its range across the cells. The white line marks the current time; click or drag on the map to move it.
  2. The vessel on the left uses the same height scale, so every height lines up with the map. It shows the selected field as a glow, liquid water as a faint blue, and the alumina melt.
  3. The overpressure first rises at the trigger and then spreads up and down the premixture. Its cross-section mean first exceeds 5 MPa at 0.55 m after 0.30 ms and at 1.10 m after 0.75 ms. The highest value, 64.8 MPa, is reached at 0.97 m after 0.725 ms.
  4. The cyan line is the pool top: the highest point where the cross-section mean liquid fraction reaches 30 %. It starts at the 1.13 m water level and reaches 1.37 m by 2 ms as steam lifts the pool.
  5. Each saved melt group is drawn as a cluster of dots about one cell across, centred on its saved position; the dots in a cluster are not individual drops. Between saved states the groups move along their saved velocities.
  6. The 4 mm drops keep their initial 2465 K, because in this model only the fragments exchange heat. The 0.1 mm fragments cool quickly: their group average falls to about 1100 K by 0.5 ms and 300 K by 2 ms.
  7. Above 1.5 m the overpressure stays below 0.2 MPa, so the steam headspace up to 2.13 m is not drawn.
  8. The K42 experiment triggered spontaneously. Here the premixture and the trigger are prescribed, so the run does not reproduce the measured pressures. Four cells across the vessel resolve little lateral detail.

Drag the vessel to turn it · click or drag on the map to move in time · space to play or pause